Sdi Wave Flowable Composite MV Shade A3

US$59.50US$69.99 (-15%)

In stock

Wave is the ideal versatile fluoride-releasing, flowable, radiopaque, light-cured composite. Wave is directly injected into the cavity preparation for maximizing adaptation to the preparation.

Estimated Free Delivery Between Friday 14th October - Sunday 6th November
Category:

Sdi Wave Flowable Composite MV Shade

Wave is the ideal versatile fluoride-releasing, flowable, radiopaque, light-cured composite. Wave is directly injected into the cavity preparation for maximizing adaptation to the preparation. The Wave shade range consists of 14 popular shades – enamel A1, A2, A3, A3.5, B1, B2, B3, C2, C3, D3, incisal, gingival, bleach; and 0A2 dentin shade. Enamel shades can be guided by VITA classical shade guide. The gingival shade is ideal for restoring cervical lesions in elderly patients. For teeth lighter than B1, bleach shade is available.

A choice of 3 viscosities-Wave, Wave MV (Medium Viscosity), Wave HV (High Viscosity).Wave, Wave MV, and Wave HV contain specially treated nano-fillers to maximize polishabilitywear-resistance, and strength. Ease of extrusion is improved with the addition of these specially treated nano-fillers.

INDICATIONS :-

  • Class V restorations
  • Tunnel/air abrasion preparations
  • Pit and fissure sealants
  • Minimal Class I, II, III, IV restorations
  • Radiopaque cavity liners
  • Cervical abrasion/erosion lesions
  • Abfraction lesions
  • Implant seals
  • Incisal abrasions
  • Repair enamel defects
  • Minor core build-ups
  • Temporary crowns
  • Cement porcelain/ceramic/ composite veneers
  • Splint mobile teeth
  • Attach fiber bridges
  • Restorations in deciduous teeth
  • Repair porcelain restorations
  • Block out undercuts in inlay/onlay/crown preparations
  • Cover stains
  • Adhering tooth jewelry
  • Ceramic inserts

Key Specifications :-

COMPOSITION WAVE:

35% wt (52 Vol%) multifunctional methacrylic ester

65% wt (41 Vol%) (0.02 – 10 micron) inorganic filler

COMPOSITION WAVE MV:

40% wt (61 Vol%) multifunctional methacrylic ester

60% wt (39 Vol%) (0.02 – 10 micron) inorganic filler

Packaging :-

  • 1 x 1g Syringe
  • 5 x disposable tips.

Direction to Use :-

Clean and Isolate tooth. A conservative cavity should be prepared, employing standard techniques and instruments, to form a slightly rounded internal form. Margins of the cavity preparation should end in sound and supported enamel with no bevels in stress-bearing locations. If bevelling is desired in a low-stress location it should extend no further than 1mm at an angle of no greater than 45°. Pre-wedging is also recommended to ensure that the restored tooth will have an adequate contact point. Prophy all surfaces to be etched including surfaces adjacent to the cavity with an oil-free non-fluoride containing paste or a slurry of pumice and water. Rinse thoroughly with water.

Shade Selection :-

Shade selection should be made with a just cleaned and moist tooth.

NOTE :- Do not use uncured paste for color matching as there is a slight color change upon curing.

Isolation:-

Isolation techniques must be used to prevent contamination. A rubber dam is the preferred mode of isolation.

Pulp Protection :-

For deep cavities, use a calcium hydroxide liner and appropriate glass ionomer cement liner to protect deep cavity reparations in close proximity to the pulp.

1. Acid Etching

Thoroughly dry the surface to be etched with dry, oil-free air. Etch tooth surface with Super Etch 37% phosphoric acid.

(a) Enamel only Etch surface for at least 20 seconds

(b) Dentin and enamel Using the “total-etch” technique etch the surface including any glass ionomer for at least 20 seconds. Enamel subjected to fluoridation should be etched for 90 to 120 seconds. Etching Precautions: Ensure that the dispensing tip hub is firmly attached to the syringe by twisting the hub securely onto the syringe. Avoid acid contact with oral tissues, eyes, and skin. If accidental contact occurs wash thoroughly with water. In the case of eye contact, wash the eye for 15 minutes, and seek medical attention. Use matrix strips to protect adjacent tooth surfaces during etching. On the first usage or after prolonged storage, extrude a small amount onto a mixing pad for familiarity with the etchant’s viscosity and rate of extrusion

2. Wash thoroughly with water

3. Remove excess water. Keep moist. Avoid contamination e.g. saliva

4. Apply Stae dentin/enamel adhesive to saturate all internal surfaces, or bonding agent according to manufacturer’s instructions

5. Blow gently with dry, oil-free air for 2 seconds to evaporate the solvent. Leave surface glossy

6. Light cure for 20 seconds (460-480nm wavelength, high power LED curing light)

7. Directly inject Wave in increments of 2mm or less in 7.1 Class V restorations, 7.2 Tunnel preparations, 7.3 Pit and fissures sealants, 7.4 Minimal Class I, Class II, Class III, and Class IV restorations. Or other indication as required.

CAUTION :-

Ensure that the dispensing tip is firmly attached to the syringe by twisting the tip hub securely onto the syringe.

Average Rating

4.84

25
( 25 Reviews )
5 Star
84%
4 Star
16%
3 Star
0%
2 Star
0%
1 Star
0%
Add a review

Your email address will not be published.

25 Reviews For This Product

  1. 25

    by nnamdi

    nano filters maximize polishability, wear-resistance, and strength…. cool product.

  2. 25

    by Massimiliano

    Thank you so much dental world . I got the product within few days

  3. 25

    by Jawara

    An ideal fluoride releasing ,Good composite at this price. Works very effectively.Thank you so much dental world . I got the product with in few days

  4. 25

    by Dante

    Products always arrive correct and in a timely fashion. also competitively priced.

  5. 25

    by Poala

    Very quick service and online ordering is very convenient.Customer saticfied

Main Menu

Sdi Wave Flowable Composite MV Shade A3

US$59.50US$69.99 (-15%)

Add to Cart